New Hardware is reader-supported: some links on this page are affiliate links, and as an Amazon Associate New Hardware earns from qualifying purchases at no extra cost to you. Learn more.
Metabo HPT C10FCGS 10-Inch Miter Saw
Metabo HPT C10FCGS cuts at 5,000 RPM, so it suits you if you need a corded saw for accurate trim work.
10 Inches blade diameter
- blade diameter
- 10 Inches
- bevel range
- 0-45 – at or above the 45° bevel reference figure
- motor power
- 15-Amp
$210 under the category median
- This Miter Saw
- $139
- Median of the 71 Miter Saws we screened
- $349
- Range
- $119 to $1799
- Cheaper than this one
- 3 of those 71
4.6/5 from 12,210 buyers
- Average buyer rating
- 4.6 out of 5
- Ratings behind it
- 12,210
- What that supports
- A large enough sample to read as a real buyer signal
- Where it comes from
- The product listing, read 5 November 2026
1 deciding spec not stated
- crosscut capacity
- Not stated in the listing – confirm with the seller before ordering
C10FCGS Overview
Metabo HPT C10FCGS Miter Saw cuts with 15-Amp power for you if you want a corded 10-inch saw for routine home and shop work.
A 10-inch blade gives you the familiar cut range of a standard shop saw, with less bulk than a 12-inch model. A 0-52 degree miter angle range also gives room for common trim angles in day-to-day work.
Metabo HPT C10FCGS pairs that format with a 15-Amp motor and a single bevel head, so the saw is built around powered cuts and one-way tilt. The 24.2 lb weight helps keep the saw easy to move for an upgrader who still wants a corded setup.
We screened 71 miter saws and selected 15 for full review. Full reviews go to the most-rated products that pass screening, at most 2 per brand. This one has 12,210 buyer ratings, the 1st most of the 71 screened. This review is for you if you want a corded miter saw for routine home repairs and trim, and you value a work clamp.
If you need more versatility, see our full review of the GCM12SD.
How New Hardware picked: we started from the 200 most-reviewed miter saw listings in our retail dataset, removed duplicates, accessories and off-category products, and 71 qualified. This product is one of 15 from that pool chosen for a full review. Our scores blend buyer satisfaction (60%), price position against comparable products (25%) and rating volume (15%). Specifications come from manufacturer listings and ratings from verified Amazon buyer reviews (data checked November 2026).
The Short Answer on the C10FCGS
Best for: you want a corded 10-inch miter saw for routine trim and 2x lumber cuts, and you value a 15-amp motor over battery portability.
Choose the C10FCGS if you want a corded saw with a 10-inch blade, 0-45° bevel range, and a 15-amp motor for around $139.
- Pro: The 10-inch blade size suits the common trim and framing cutoff for this category.
- Pro: The 15-amp motor gives you enough drive for routine 2x lumber work.
- Pro: A 0-45° bevel range supports standard compound cuts for crown and casing.
- Con: It is single bevel, so you must flip the work for opposite-leaning compound cuts.
- Con: At 24.2 lbs, it is not the lightest option among the saws we screened, so frequent carrying is less convenient.
Don’t buy this if: you need a double-bevel saw for faster repeated angled cuts without flipping the work.
Price assessment: $139 is a low price for a corded 10-inch saw with a 15-amp motor and a 5-year warranty.
New Hardware score: 9.4/10 (data-driven – see “How we picked” above)
New users should consider the best miter saw for beginners to start their projects.
Specifications in Full
| Spec | Value |
|---|---|
| Blade diameter | 10 Inches |
| Bevel range | 0-45 |
| Crosscut capacity | Not stated |
| Motor power | 15-Amp |
| Weight | 24.2 lbs |
| Work clamp | Yes |
| Corded or cordless | corded |
| Bevel type | single bevel |
| No-load speed | 5,000 RPM |
| Warranty | 5-year warranty |
Bevel range is the deciding spec that most separates the C10FCGS here. It measures how far the saw head can tilt sideways for angled cuts.
Before You Buy: Mitre Saw Checklist
The first thing to check is crosscut capacity, because wide boards and trim fail fast when the saw cannot take them in one pass. C10FCGS states a 10-inch blade, a 0-52 degree miter range, and a 0-45 degree left bevel.
- ☐ Confirm the board width you plan to cut — the 10-inch blade size is the key figure here, and if your trim is wider than the saw can handle in one pass, you will need a different saw or a second cut.
- ☐ Check your crown-molding angle needs — the left bevel range is 0-45 degrees, so the saw can handle easier crown cuts, but steeper compound work will force you to flip the work or buy a different model.
- ☐ Measure your available power setup — 120 Volts and corded electric power mean you need a nearby outlet, or you will be stuck reworking the setup around cord reach.
- ☐ Budget for the weight you will move — 24.2 lbs means this saw is not a featherweight carry, and a buyer who wants frequent transport may end up living with the extra bulk.
- ☐ Confirm you want a single-bevel saw — the head tilts left only, so right-leaning compound cuts require repositioning the stock and slow the workflow.
Do not buy this saw if you need double-bevel convenience or wider one-pass crosscuts than a 10-inch miter saw can provide.
What These Specifications Let You Do
What 15-Amp Cutting Power Suits
The C10FCGS is a 10-inch corded miter saw with a 15-amp motor, so it suits routine trim work and 2x lumber cuts in a home shop. That motor size is enough for the easier end of repeated cutting, and it is the figure that matters most if you want steady drive from a wall outlet rather than a battery pack.
The 1950-watt draw and corded electric supply point to a saw built for continuous use at the bench, while the 24.2 lb weight keeps it portable enough for moving between rooms or a jobsite.
What the 0-45 Degree Bevel Range Allows
C10FCGS gives you a left bevel range from 0-45 degrees, which is enough for standard compound cuts on crown and casing. That matters because a 45° bevel is the category point that enables those angled cuts, and this saw states that figure directly.
The miter angle range runs from 0-52 degrees left and right, so you can set common picture-frame corners and many trim joints without forcing awkward workarounds. A single bevel head still means the tilt goes one way only, so repeated compound cuts are slower than on a double-bevel saw, but the adjustable bevel stops and thumb-actuated positive stops help keep common settings quick to return to.
How the Table and Clamp Help Cutting
That combination helps when you are cutting short casing pieces or matching several identical stops, because the stock stays organized around the cut line.
Its work clamp is listed, which matters when you want the piece secured for repeat cuts instead of hand-holding every board. The 5-year warranty adds long-term ownership context, and the 25-pound item weight keeps the saw manageable when you need to move it after setup.
The C10FCGS Job by Job: What Its Figures Cover
The C10FCGS against the jobs buyers ask about, worked out from its listed bevel range and motor power and a typical need for each job.
| Job | What it takes | C10FCGS |
|---|---|---|
| Cut crown molding with the saw tilted for inside and outside corners | at least 45 to 50 degrees | Only at the easier end of that range – 45 degrees |
| Run a cordless saw all afternoon on trim and framing cuts | at least 15 to 20A | Only at the easier end of that range – 15A |
| Cut 2x lumber for home repairs with enough drive for routine work | at least 10 to 15A | Yes – 15A |
The C10FCGS Against Similar Miter Saws
C10FCGS gives you a 10-inch blade, a 15-amp motor, and a 0-45° left bevel range for a $139 corded saw. That mix matters because the bevel range supports compound cuts, while the 15-amp motor is the drive figure you compare for routine trim and 2x work.
- Against the Metabo HPT C12RSH2S, C10FCGS gives up the 12-inch blade and keeps the lower price at around $139. If you need wider crosscut capacity, the larger blade is the reason to spend the same amount.
- Against the DOVAMAN DMS01A-Upgraded, C10FCGS trades away sliding-rail capacity and keeps the simpler fixed format. The DOVAMAN listing states a 13-inch sliding rail, which matters when you need more reach across wider stock.
- Against the Hoteche 7-1/4-Inch model, C10FCGS uses a 10-inch blade instead of 7-1/4 inches. That larger blade size is the better fit when you want the more common trim and framing format.
- Against the Metabo HPT C10FCGS listing priced at $148.99, this C10FCGS is around $9.99 cheaper. That gap matters if you want the same 15-amp motor without paying extra for a different listing.
- Against the Ryobi 18V ONE+ HP, C10FCGS is corded rather than battery-powered. That makes it the better pick when you want steady mains power instead of portability.
- C10FCGS ranks first on buyer rating in this comparison, at 4.6 from 12,210 ratings. That is the only rating edge here; the purchase decision still turns on the 10-inch blade, 15-amp motor, and bevel range.
Choose the DOVAMAN if you need a sliding rail for wider crosscuts. Choose the C12RSH2S if the 12-inch blade matters more than staying at this price.
What the deciding spec costs here: Measured as price per unit of bevel range, the reviewed product works out to $3.09 against a $6.36 median across the 54 other screened products that state the spec, and 4 of them deliver more of it per dollar. The cheapest screened product that beats its 0-45 is the S26-262L at $119 with 0- 47, which is $20 less than this one for more of the spec that decides this category.
Explore other ways to achieve similar results without using a traditional saw.
What Value for Money Looks Like Here
At around $139, the C10FCGS sits $2 below the $141 average for the similar miter saw products we compared it against. That price leaves you with a 10-inch blade, a 15-Amp motor, and a single-bevel layout, so you give up the faster left-right tilt of a double-bevel saw and keep the corded setup.
Choose it if you want a corded 10-inch miter saw with 0-45 degrees of bevel travel, 0-52 degrees of miter range left and right, and a 5,000 RPM no-load speed. The 24.2 lb weight and included work clamp matter if you plan to move it often and want the stock held in place during repeat cuts.
Where this sits in the buyer data: Among the 71 products screened for this category, this one’s 4.6 rating places it #16, on 12,210 ratings – above the 92-rating median of that group, so the average rests on more feedback than most of its comparables. On price it undercuts 66 of them.
Setting Up This Miter Saw, and What Support Covers
What C10FCGS needs before first cut
C10FCGS needs a 120-volt corded outlet before it does any useful work.
- Unpack the saw and confirm the blade diameter is 10 inches before you mount any replacement blade.
- Place the saw where a corded electric tool can reach a 120-volt supply without strain.
- Set the bevel to the left-side 0-45-degree range for the angle you need, then lock it in place.
- Choose a miter angle within the 0-52 degrees left and right range for the cut you want.
- Fit a 10-inch miter saw blade and, if you want chip capture, add a dust bag that matches the saw’s 10-inch blade diameter.
Warranty and support checks for this mitre saw
Warranty cover varies by seller and country.
- Confirm the return window for a 15-amp corded saw, because the motor and switch are not user-serviceable parts.
- Confirm whether the seller includes blade support or only the saw body, because the blade size must stay at 10 inches.
- Confirm whether a dust bag is included, because the listing states a vice clamping system but does not state a dust-collection bag.
On arrival, check the box contents and the 10-inch blade fit before the return window closes.
C10FCGS Buying Questions Answered
What the C10FCGS gives you for trim and framing cuts
The C10FCGS uses a 10-inch blade and a 15-Amp motor. That pairing suits routine trim and framing work, where a corded saw matters more than battery portability.
Bevel range and compound cuts
C10FCGS lists a left bevel range from 0-45 degrees. That makes standard compound cuts possible for crown and casing work, while the single-bevel layout still keeps the head tilting one way only.
Crosscut capacity and stock size
The C10FCGS does not list crosscut capacity. That means wide-board fit is the number to check elsewhere in your comparison, because blade diameter alone does not tell you the cut width.
Weight and setup
C10FCGS weighs 24.2 lbs. That is light enough to matter if you move the saw between jobs, and the work clamp can help hold stock during repeat cuts.
How much power does the Metabo HPT C10FCGS 10-Inch Miter Saw have?
The C10FCGS has a 15-Amp motor and a no-load speed of 5,000 RPM. That gives you a clear corded setup for routine 2x lumber work, and the listed wattage is 1,950 watts.
Is the Metabo HPT C10FCGS 10-Inch Miter Saw good for crown molding?
Yes, the C10FCGS has enough bevel travel for crown molding at the easier end of the usual range. The saw lists 0-45 degrees on the left, so the angled setup is there, but the single-bevel format still means you flip the work for opposite-direction cuts.
Does the Metabo HPT C10FCGS 10-Inch Miter Saw run on batteries?
No, the C10FCGS runs on corded electric power. Its 120-volt supply and 15-Amp motor point to outlet-powered use, not battery portability.
Is the Metabo HPT C10FCGS 10-Inch Miter Saw heavy to move around?
The C10FCGS weighs 24.2 lbs, or 25 pounds in the item weight field. That is manageable for moving between a bench and a vehicle, but it is not a featherweight saw.
Should I buy the Metabo HPT C10FCGS 10-Inch Miter Saw for home repairs?
If your work is mostly 2x lumber and trim, the C10FCGS fits that job well. The 15-Amp motor is the key number here, and the $139 price keeps the entry cost low for a corded saw.
Is the C10FCGS Right for You?
Who the C10FCGS suits and the jobs it is the wrong choice for, listed below with the reason for each.
Who the C10FCGS is for, and what it does well
Who this mitre saw suits
- DIY homeowners cutting trim and molding — the 10-inch blade, 15-amp motor, and 5,000 RPM speed suit common finish carpentry cuts
- Apartment or garage workshop users with limited space — the 25-pound weight and corded 120-volt power make it easier to move and set up on a bench
- Budget-conscious first-time miter saw buyers — the $139 price and simple positive-stop miter settings fit basic home projects without a big investment
- Woodworkers making small furniture and shelving — the 0-52 degree miter range and 0-45 degree left bevel handle angled cuts for frames and boxes
- Landlords or property managers doing occasional repairs — the vice clamping system and adjustable bevel stops help with repeatable cuts on trim and boards
- Students in carpentry or construction classes — the 10-inch table, thumb-actuated positive stops, and 5-year warranty suit learning standard saw setup and operation
What this miter saw handles well
- Baseboard and crown molding cuts — the 10-inch blade and 0-45 degree left bevel range support common trim angles
- Picture frame and box miter joints — the 0-52 degree left and right miter range supports angled corner cuts
- Cutting 2x lumber for small framing jobs — the 15-amp motor and 5,000 RPM blade speed handle typical softwood cuts
- Repeat angle cuts for shelving or furniture parts — the thumb-actuated positive stops make common miter settings quicker to return to
- Beveled trim fitting around rooms — the adjustable bevel stops support consistent left-side bevel cuts
- Portable bench-top cutting in a garage or driveway — the 25-pound weight and corded electric power make it easy to move and plug in
What this miter saw is the wrong choice for
- Large sheet goods crosscutting — the 10-inch blade and miter-saw format are not suited to breaking down full plywood sheets
- Right-side bevel-only workflows — the bevel range is 0-45 degrees left only, so it does not bevel to the right
- Heavy-duty production framing all day — the 15-amp consumer motor and $139 price point are not built for industrial throughput
- Deep thick-stock cuts in one pass — the 10-inch blade size limits cut capacity compared with larger saws
- Dust-sensitive indoor finishing without cleanup gear — no dust collection spec is listed, so it is not the right choice for a clean-room setup
What to budget alongside this mitre saw, and what to skip
Accessories worth buying with this mitre saw
- Miter saw blade — the saw needs a 10-inch blade to cut, and the specs list blade material but not a spare blade
- Saw stand or workbench support — the 25-pound bench-top saw needs a stable surface to use safely
- Extension cord — it is corded electric and needs mains power beyond the saw’s cord reach
- Clamps — the vice clamping system is included, but extra clamps help secure longer workpieces and odd shapes
- Safety glasses — the saw spins at 5,000 RPM and cutting wood throws chips and dust
Accessories you can skip buying for this miter saw
- Battery pack — this is corded electric, so no battery system is needed
- Right-bevel accessory kit — the bevel range is only 0-45 degrees left, so right-side bevel add-ons are unnecessary
- Large sliding saw upgrade — this is a fixed miter saw style, so paying for sliding capacity would be wasted here
Where to Buy This Miter Saw
When we looked in November 2026, the C10FCGS was listed at $139 – a snapshot that may have changed since.
Miter saws are sold by the retailers below – we do not track which of them has the C10FCGS in stock, so check availability and the current price with the retailer before making a trip.
- Home Depot (online and physical stores) — broad range of mainstream miter saws and easy in-store returns
- Lowe’s (online and physical stores) — broad selection for DIY buyers and convenient physical-store pickup
- Amazon (online only) — wide assortment across brands and models
- Acme Tools (online only) — specialist retailer with knowledgeable power-tool focus
- Northern Tool (online and physical stores) — useful for tool-focused shopping and in-store pickup
- Ace Hardware (online and physical stores) — local-store convenience for common miter saw options
- Walmart (online and physical stores) — broad mass-market assortment and easy returns
Final Verdict on the C10FCGS
You should choose the C10FCGS if you want a corded 10-inch miter saw with a 15-Amp motor for routine trim and 2x lumber work, and it’s around $139.
The 0-45° bevel range gives you the tilt needed for standard compound cuts, and the 5,000 RPM no-load speed adds useful headroom for quick repeat cuts.
Skip it if: you need a sliding saw for wider crosscuts, or you want a cordless setup for work away from an outlet.
Warranty details: see the official Metabo HPT warranty page.